| Posted By |
Discussion Topic:
Engine won’t go up hills
-- page:
1
2
|
|
wolfie |
08-17-2024 @ 7:37 PM
|
|
|
|
New Member
Posts: 146
Joined: Oct 2009
|
I have a 40 V8 that has a hard time with acceleration and hills. It starts easily and Idles good. I have adjusted the carburetor with no success. There has been an electronic ignition installed, but the problem is the same. The fuel filter doesn’t have sediment and the filter is fairly new. Any ideas on what the problem might be? Thanks in advance for your help!
|
carcrazy |
08-17-2024 @ 11:26 PM
|
|
|
|
Senior
Posts: 1979
Joined: Oct 2009
|
The lack of enough power to climb hills or accelerate could be caused by many different issues. One or more brakes could be dragging excessively. The fuel supply may not be sufficient to provide the power required. Ignition timing may be retarded. The engine may be worn out with very low compression due to leaking piston rings or valves. Something could be restricting the flow of air into the engine or exhaust out of the engine.
|
MG |
08-18-2024 @ 12:59 PM
|
|
|
|
Senior
Posts: 1301
Joined: Nov 2009
|
Slipping/worn clutch disc assembly...
|
40cpe |
08-18-2024 @ 4:30 PM
|
|
|
|
Member
Posts: 488
Joined: Jan 2010
|
60 HP or 85 HP?
|
wolfie |
08-18-2024 @ 8:40 PM
|
|
|
|
New Member
Posts: 146
Joined: Oct 2009
|
It’s 85 hp. The clutch isn’t slipping. It might be a fuel flow restriction.
|
trjford8 |
08-19-2024 @ 7:00 AM
|
|
|
|
Senior
Posts: 4354
Joined: Oct 2009
|
If you are seeing sediment in the fuel bowl I suspect you have a junk in the gas tank. You may have a tank that sealer was put in it and now the sealer is starting to come loose or the tank is rusty inside. Remove the sending unit and look inside.
|
JayChicago |
08-20-2024 @ 8:15 AM
|
|
|
|
Senior
Posts: 555
Joined: Jan 2016
|
From the original post: “The fuel filter doesn’t have sediment and the filter is fairly new. ”
|
carcrazy |
08-20-2024 @ 9:04 AM
|
|
|
|
Senior
Posts: 1979
Joined: Oct 2009
|
A couple of easy and simple tests can be done to determine why the engine lacks power. Using a vacuum gauge, check to see what the manifold vacuum reading is at idle. A healthy engine will show 19" or more at sea level. Use a compression gauge to measure the compression of each cylinder. All of the cylinders should be within about 10 PSI of each other with about 100 PSI or more for each cylinder.
|
37RAGTOPMAN |
08-20-2024 @ 4:55 PM
|
|
|
|
Senior
Posts: 1992
Joined: Oct 2009
|
MAKE SURE you have full throttle., depress the gas pedal, or place a piece of wood on the gas pedal [ or have someone push it down ] then check the carburetor linkage to make sure it is as far as it will go. also check you air filter for any dirt, HOW OLD IS THE GAS ? try driving the car with out one, to see if it make a difference, [ it might be a little clogged ] do a ggod tune up starting with a compresson test. each cylinder should be within 20 lbs of each other if it not good, try a leak down test to find out what is the problem get back to us with results, hope this helps 37 Ragtopman, Maine
|
Drbrown |
09-06-2024 @ 9:13 AM
|
|
|
|
Senior
Posts: 609
Joined: Nov 2013
|
How exactly does the engine behave when climbing hills ? Do the RPM's simply not increase or does the engine shutter/stumble like a bad spark plug, plug wire or a bad distributor condenser might do. If the indicator in your your vacuum gage rides steady the valves should be okay.
|