Posted By |
Discussion Topic:
Fog Lights:
-- page:
1
2
|
|
39 Ken |
10-16-2018 @ 4:49 AM
|
|
|
Member
Posts: 380
Joined: Oct 2009
|
Most, if not all the fog lite switches I have seen have a built in fuse holder. Ken
|
sarahcecelia |
10-15-2018 @ 11:48 AM
|
|
|
Senior
Posts: 1171
Joined: Mar 2013
|
Yes, good idea; I thought it was superfluos to mention that.
Regards, Steve Lee
|
trjford8 |
10-10-2018 @ 9:26 AM
|
|
|
Senior
Posts: 4202
Joined: Oct 2009
|
I would also install an in-line fuse.
|
sarahcecelia |
10-10-2018 @ 6:56 AM
|
|
|
Senior
Posts: 1171
Joined: Mar 2013
|
All you really need is a hot wire (negative)"jumpered" from one light to the other and a ground wire (positive) "jumpered" from one light to the other. Install a little toggle switch on the lower edge of the instrument panel. with a hot wire on the "in" pole and the other (out)pole going to the lights, and that's it! Easy?? Yes!! Regards, Steve Lee
This message was edited by sarahcecelia on 10-15-18 @ 11:46 AM
|
trjford8 |
10-08-2018 @ 10:43 AM
|
|
|
Senior
Posts: 4202
Joined: Oct 2009
|
Rather than use them for fog lights I have used them for turn signals. Those coming in the opposite direction can't miss them.
|
TomO |
10-08-2018 @ 6:58 AM
|
|
|
Senior
Posts: 7243
Joined: Oct 2009
|
The fog lamps are not adjustable up and down, so make sure that you have them aimed to the right side of the car. You don't want them to blind the oncoming drivers. You asked if the 6 volt system would stand burning fog lights and head lights at the same time, the answer is a qualified yes. The qualifications are the condition of the battery, the charging system and driving conditions. If either the battery or the charging system are marginal, you could run down the battery with both sets of lights on. Pay attention to you battery gauge and watch for a discharge condition while driving. Short trips or stop and go traffic conditions could also lead to a discharged battery. If you are not going to use the Ford bullet connectors or solder the wires, I would use a small wire nut (available at the hardware store) to hold the wires together. To use it, you just twist the wires together and then screw on the wire nut. Then I would use electrical tape to keep the weather out of the connection. I would use 14ga wire from the connection to the switch. You can use the switch that you provided a link to. If you look carefully at the back of the switch, you will see that 2 of the connectors are connected. The left connector is for power in to the switch and the 2 right connectors are the switced connectors. The grounding is done from the bulb socket to the fog lamp and through the clamp to the bumper bracket.
Tom
|
fortyford |
10-07-2018 @ 12:58 PM
|
|
|
Member
Posts: 206
Joined: Nov 2009
|
OK,Thanks Kube and Tom for all the help.
This message was edited by fortyford on 10-7-18 @ 1:00 PM
|
kubes40 |
10-07-2018 @ 11:34 AM
|
|
|
Senior
Posts: 3370
Joined: Oct 2009
|
You can get that type of connector but simply enough, just twist the two together and (I prefer solder) attach to the wire leading to the switch. Mike "Kube" Kubarth
This message was edited by kubes40 on 10-7-18 @ 1:10 PM
|
fortyford |
10-07-2018 @ 10:21 AM
|
|
|
Member
Posts: 206
Joined: Nov 2009
|
Is there something electrical i can get at auto shop to tie both lights into behind grill and then just run one wire to switch?
|
kubes40 |
10-07-2018 @ 9:41 AM
|
|
|
Senior
Posts: 3370
Joined: Oct 2009
|
Originally the two lamp (leads) were connected just behind the fender and one wire was routed from there to the dash panel.
Mike "Kube" Kubarth
|