Early Ford V-8 Club Forum

EFV-8 Club Forum / General Ford Discussion / valve train removal tools

Reply to Discussion | New Discussion << previous || next >>

Posted By Discussion Topic: valve train removal tools     juergen 07-23-2011 @ 3:25 PM reply profile send p.m. Member Posts: 275 Joined: Jan 2010 Speedway sells a stainless steel set for about $350 Joblotauto in NY sells a complete set for $250. 37RAGTOPMAN 07-23-2011 @ 7:07 AM reply profile send p.m. Senior Posts: 1992 Joined: Oct 2009 I had one engine were it was pretty rusted up, what I did was raise the valve and cut the heads off with a cutting torch, being I was going to install everything new anyway, and just soaked everthing with RUST BUSTER,and drove the guides out, if you have all the FORD TOOLS,you might be able to save a few parts, but not really worth it, being it is a lot of work to do once, and a lot more work if you have to redo it, my 3 cents worth 37RAGTOPMAN you have to rememeber Ford had many tools to remove the valve train, do your reserch MICHV8 07-22-2011 @ 7:56 PM reply profile send p.m. Senior Posts: 500 Joined: Jul 2010 any suggestions for suppliers This message was edited by MICHV8 on 7-22-11 @ 8:21 PM MICHV8 07-22-2011 @ 7:56 PM reply profile send p.m. Senior Posts: 500 Joined: Jul 2010 juergin: I like that idea...thanks for the tip. juergen 07-22-2011 @ 5:08 PM reply profile send p.m. Member Posts: 275 Joined: Jan 2010 As far as getting the valves out, welcome to flathead h*ll. By the book the long bar will get the valve guide down to take out the horse shoe clip. Then you could use the bar to push up the entire assembly. Nice dream but the guides are usually stuck in place. So you can use the bar to get the U shaped spring retainer off the tulip valve end. Then you can push the valve up so that a special dog leg tool can be used to knock down the guides to remove the horse shoe clip that holds the valve guide in place. However I don't know anyone who sells this tool. I just got done taking apart a 37 where the crank was not stuck but the valve guides were. Half way through the dissassembly with the hardened tool, it broke. Now the last resort approach is to say good bye to those mushroomed valves and replace them with 49-53 valves and guides. If this is your choice, after lifting the valve up, break off the face of the valve, use the bar to force the spring out the bottom and then drive the stuck guides down with a punch. Replace with a 49-53 drive train and with adjustable lifters. No one will see it and you can do the work yourself. TomO 07-22-2011 @ 7:39 AM reply profile send p.m. Senior Posts: 7386 Joined: Oct 2009 IMHO, you would be better off having the engine rebuilt before installing it in the car. Just doing a valve job, without knowing the condition of the engine, could lead to having to do the work over after installing the engine in the car. You did not say whether you know if the engine burns oil or if it has sufficient compression, or the bearings are in good condition. Disassembling the engine to determine condition and not doing the repair work is never a good idea as you will have to do the work some time later. Tom MICHV8 07-21-2011 @ 7:02 PM reply profile send p.m. Senior Posts: 500 Joined: Jul 2010 Glad to! Bought a car with no engine. Bought engine. Engine out of car. Removed heads, but not manifold. Valves have too much wiggle room. Don't see rust. This message was edited by MICHV8 on 7-21-11 @ 7:03 PM oldford2 07-21-2011 @ 12:56 PM reply profile send p.m. Member Posts: 275 Joined: Oct 2009 Can you provide more detail. Why did you start this project? Engine burning oil, low compression. Have you removed the intake yet? Is the engine in or out of the car? This message was edited by oldford2 on 7-21-11 @ 4:05 PM BrianCT 07-21-2011 @ 9:46 AM reply profile send p.m. Member Posts: 98 Joined: Oct 2009 You are right about valve guides being a pain. If they are worn then you may also need to replace the valves . In that case you could just remove the bottom spring keeper to release some of the pressure , then raise the valve as much as possible and drive the guide down from above. MICHV8 07-21-2011 @ 8:50 AM reply profile send p.m. Senior Posts: 500 Joined: Jul 2010 I have the heads off a 37 block and the cylinders look good, but the valve guides appear shot. I will check the rings, but never did a valve job before. Other than the long bar, any special tools to help disassembly? I'm guessing the exhaust guides will be the most stubborn. Any advice or publications? Thanks folks...

<< previous || next >>

NOTE: YOU MUST BE A REGISTERED USER AND BE LOGGED IN TO POST (and reply to) messages in this forum. If you are a first time user, please click the CREATE A NEW ACCOUNT in the masthead above to register and Log In. After that, all you do is LOG IN to enjoy using this site.

DISCLAIMER: The V-8 Club does no independent testing of any of the opinions, thoughts or suggestions presented in the website on the Forum, in the Tech Tips section, or any section. A reader should consider the website to be a forum wherein differing solutions to a particular set of circumstances may be discussed. Ultimately, the selection of an item for an individual's vehicle must be based upon the independent study of the vehicle owner in consultation with people in the hobby and restoration experts.

EFV-8 Club Forum Home | Back to Home Page | Contact the Webmaster

Copyright © 2009 - EFV-8.org
Powered by < CF FORUM > v.2.1