| Posted By |
Discussion Topic:
6 Volt Electric Fuel Pump
-- page:
1
2
|
|
Grant |
05-25-2019 @ 7:09 AM
|
|
|
|
Senior
Posts: 559
Joined: Oct 2009
|
Hello Harry. The low-pressure Airtex E8902 installed on our '36 Ford works just fine. It is controlled by an on/off toggle switch under the dashboard. Mounting it on the side of the chassis close to the gas tank is important, in my opinion. The pump is protected with a cover plate made from a bread pan filched from my wife's pantry ........ can post a photo if that would help you.
|
sarahcecelia |
05-24-2019 @ 1:07 PM
|
|
|
|
Senior
Posts: 1196
Joined: Mar 2013
|
Put the toggle switch on the lower edge of the dash, driver's door side. Mount it so forward is on, back is off; Just like your brake pedal and gas pedal. Makes it easy to remember which is which! P.S. never have needed it; I just put one in the system in case I ever got so called " vapor lock", which after driving (2) 1950 v8's for thousands of miles( (one when I was 18 years old) I never got, and never heard of, until I joined the club about 8 years ago!! Is it a "Fairy Tale?" It is to me.
Regards, Steve Lee
|
37RAGTOPMAN |
05-24-2019 @ 11:31 AM
|
|
|
|
Senior
Posts: 1992
Joined: Oct 2009
|
if you use a electric pump, I would use a push button switch, so it shuts off when done priming , or wire it in so it goes off when engine starts., or if you are going to use as a main pump make it goes off when engine is shut off, for SAFETY SAKE, I do not use one, I would rather crank the engine to build up oil pressure, and not start the engine dry after sitting for long periods of time, hope this helps. 37RAGTOPMAN
|
lkelton4 |
05-24-2019 @ 9:43 AM
|
|
|
|
Member
Posts: 3
Joined: Dec 2018
|
I was planning on adding a fuel pump with a toggle switch to my 36 Coupe. Any recommendation on the toggle switch and where did you install it on the dash? Would love to see a picture of where it is installed. Thanks.
lkelton4 ‘36 Deluxe Coupe
|
sarahcecelia |
04-21-2019 @ 8:14 AM
|
|
|
|
Senior
Posts: 1196
Joined: Mar 2013
|
Randy Rundle @ Fifth Ave Garage,Clay Center, Kansas City has a REAL NICE PUMP THAT WORKS ON 6 OR 12 VOLT with no alterations to you electrical system..It's small and compact, and silent!!
Regards, Steve Lee
|
supereal |
04-20-2019 @ 9:16 AM
|
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
We get ours at C&G. 11A-9350-E6 6 volt About $70. The one on my '47 has give 25 years of service (so far).
|
Hrussell8750 |
04-20-2019 @ 7:39 AM
|
|
|
|
Member
Posts: 31
Joined: Jun 2016
|
Thank you Ron, I will be looking in to that pump.
Thank You, Harry8750
|
carcrazy |
04-19-2019 @ 8:27 PM
|
|
|
|
Senior
Posts: 1979
Joined: Oct 2009
|
One source for a 6 Volt fuel pump that provides 2.0 to 2.5 PSI fuel pressure is Fifth Avenue Antique Auto Parts. This pump which includes a 30 micron filter can be wired up for either positive or negative ground. For more information or to order a pump, contact Randy Rundle at 785-632-3450.
|
51woodie |
04-19-2019 @ 7:40 PM
|
|
|
|
Senior
Posts: 561
Joined: Jan 2017
|
I installed a 6 volt Airtex E8902 on my '46 coupe in 2018, which I bought from Rockauto for $32.00. I only use it for "priming' after the car has sat for a number of days. It works well for me, has the right pressure, and is a "flow through" design, which allows the engine fuel pump to provide flow to the carb when the engine is running. I also used the metal fuel filter with threaded connection to the inlet of the pump.
|
Model B |
04-19-2019 @ 7:39 PM
|
|
|
|
Member
Posts: 93
Joined: Oct 2009
|
Ron is correct. You might try Amazon also. They usually trend at around $30. Good luck, Pat
|