Posted By |
Discussion Topic:
overdrive solenoid
-- page:
1
2
|
|
Drbrown |
07-25-2017 @ 9:20 PM
|
|
|
Senior
Posts: 563
Joined: Nov 2013
|
I don't know if this will help but I can email you four Borg-Warner Manuals dealing with operation, rebuilding, use tips, and wiring. The files are in *.pdf format and too large to attach here. Email me at gfdanbrown@yahoo.com and I'll send them. If yahoo.com thinks the files are too large I'll send them via my gmail account. Dan Brown
|
sarahcecelia |
07-21-2017 @ 4:32 PM
|
|
|
Senior
Posts: 1171
Joined: Mar 2013
|
Where are you moving to in SW Florida? I'm in Spring Hill, SW Florida. I and do all my own mechanical work.I have a lot of knowledge as I worked as a mechanic in the late 60's, VW and Buick-total about 10 years, I have loads of tools, a lot from starting in my teens(1955), and lift on the property.
Regards, Steve Lee
|
sarahcecelia |
07-21-2017 @ 4:24 PM
|
|
|
Senior
Posts: 1171
Joined: Mar 2013
|
Your right all of those solenoids for sedans and convertibles are the same.The convertible had a special Ell brackett, to make it clear the x frame but stll used the same solenoid.
Regards, Steve Lee
|
tomlud |
07-21-2017 @ 11:24 AM
|
|
|
Member
Posts: 23
Joined: Jan 2011
|
Thanks to all of you who responded. I'm in the process of moving to SW Fla so hopefully when I get settled their the local regional chapter can assist me in finding a good mechanic. Thanks again. Tom.
|
39 Ken |
07-21-2017 @ 3:23 AM
|
|
|
Member
Posts: 380
Joined: Oct 2009
|
The original Borg Warner overdrive manual is on line thanks to the Studebaker Club in Ga. http://www.studebakerclubs.com/NorthGeorgia/Overdrive.pdf
|
sarahcecelia |
07-20-2017 @ 6:36 AM
|
|
|
Senior
Posts: 1171
Joined: Mar 2013
|
You can test the solenod by running a "hot" jumper wire to the terminal that is closest to the end cap. Just "strike it" on the terminal. You should hear the solenoid "jump." You can also test it out of the car. Just ground it and touch a hot wire to that terminal. You can clean the points with a small piece of 400 sandpaper, or something close to that like 320. After cleaning them , pull a paper business card between the contacts to take off any residue. If you need to take the solenoid out , you have to turn it about 1/4 turn to the right to remove it. Putting it back in you have to engage the pawl on it into the trans, and turn it 1/4 turn to the left. If it is in properly, before you put the two bolts back in, you should be able to pull on it and feel a sprng tension. All of this is explained in Randy Rundles O'drive booklet. You should really get one before you damage something by not knowing what your doing! Call him @785-632-3450. keep trying he's very busy!
Regards, Steve Lee
|
sarahcecelia |
07-19-2017 @ 8:08 PM
|
|
|
Senior
Posts: 1171
Joined: Mar 2013
|
Randy Rundle sells a booklet, at a nominal cost, telling you everthing you need to know about overdrive and how it works, trouble shooting it, and drawings of the wireing. With that booklet, you can fix it yourself.
Regards, Steve Lee
|
sarahcecelia |
07-19-2017 @ 7:54 PM
|
|
|
Senior
Posts: 1171
Joined: Mar 2013
|
"Everything on the overdrive system will work with 6 or 12 volts, with the exception of the solenoid. It will work on 12 volts for a short time, but then it will go bad.You have to buy a 12 volt solenoid if you convert to 12 volts." per, Randy Rundle, Fifth Garage, Clay Center, Kansas City, Kansas. Regards, Steve Lee
This message was edited by sarahcecelia on 7-19-17 @ 8:03 PM
|
tomlud |
07-19-2017 @ 4:07 PM
|
|
|
Member
Posts: 23
Joined: Jan 2011
|
if any of the points are "burned" can they be cleaned and can the solenoid likely be salvaged or does it need to be replaced? The car is still a 6 volt system.
|
supereal |
07-19-2017 @ 2:02 PM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
The problem is likely the "hold" set of points in the solenoid. There are two sets under the end cap, one to energize the solenoid to engage the overdrive, and the other to hold it engaged until the power is off. This reduces the amount of current needed to pull the solenoid, and lets the "hold" points keep it engaged. Either the "pull" points are stuck together, or the "hold" set is dirty or burned. At our shop we see this when a 6 volt car is converted to 12 volts. As for the difference between the open and closed cars, it is in the "elbow" adapted that lets the solenoid clear the "X" brace on the frame. The rest is the same.
|