Posted By |
Discussion Topic:
'51 8BA RPMs
-- page:
1
2
|
|
wmsteed |
12-05-2009 @ 8:14 PM
|
|
|
Senior
Posts: 606
Joined: Oct 2009
|
Clark had two 5 spd transmissions that were offered starting sometime in the mid 1950's through the early '70's. One of the Clark 5 spd's was direct in 5th year. The other Clark 5 spd was an OD in 5th gear. This Clark trans is usually found in school bus and ambulance chassis', F-3/F-5, F-350/F-500, GM C-30/C-50. I read an article in 4x4 Off Road about this trans about ten years ago. The article was about serious off roaders that were having trouble with their newer aluminum cased 4 spd's that were coming apart under hard off road use. The old T-98/T-18 rock crusher, granny geared transmissions were being adapted into a lot of the off road trucks, the one disadvantage was slow hiway speeds. The Clark 5 spd solves this problem because of the granny low gear and an OD. Of course because of the age, the OD Clark's are hard to find, fortunately I saved the article so every time I run into an old Clark 5 spd I can look up the case numbers. Many years ago I purchased an old Ford farm hand... For you city boys, the farm hand was a truck that had been cut down, removing the body and turning the controls around so the truck was operated backwards, the steering axle to the rear. A cable or hydraulic operated set of forks were mounted on the truck to pick up large piles of hay. The farm hand I purchased turned out to be an old school bus... you guessed it... the tranny was a Clark 5 spd OD.. I have been thinking about putting the Clark in my '59 F-100 4 x 4.
Bill 36 5 win delx cpe
|
supereal |
12-05-2009 @ 11:23 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
My late father-in-law had an F-2 with a three speed column shift that he used to haul heavy cream cans for his business. It had a high ratio rear end to give it enough power to handle the load, but was limited to about 50 mph in high gear. He had ordered it that way to get a full synchro transmission, as he hated the 4 speed in his other trucks. I haven't seen a four speed with OD in light trucks. Most had a "granny gear" low gear to haul big loads in hilly territory.
|
wmsteed |
12-05-2009 @ 7:22 AM
|
|
|
Senior
Posts: 606
Joined: Oct 2009
|
I guess I should clarify my earlier statement about Ford using 3.89 as "the standard ratio in OD equipped vehicles". This statement applies to the F-1/F-100 series of trucks only. I don't believe that Ford ever equipped any of the F-2/F250 trucks with OD's. I have had a couple of trucks with factory OD's, the last one being a '59 F-100, big window Custom Cab, 292 V8, w/PS, PB, radio and fresh air heater. The truck had a style-side 6' box. The truck was not really a EFV8, however is was still from the '50's, it was a great truck. I sold the truck about five years ago because a guy offered me a lot of money for the truck. I still have a '59 F-100 V8 4x4. It is also a big win custom cab with a lot of factory accessories.
Bill 36 5 win delx cpe
|
Big Red 51 |
12-04-2009 @ 2:53 PM
|
|
|
New Member
Posts: 192
Joined: Oct 2009
|
Bill, Thanks for all the good info. I agree a factory setup would be the best. The 4.27 is not all that bad if you stay under 55. It sure is nice driving around town or hills. Hardly ever need to use first.
|
wmsteed |
12-03-2009 @ 6:17 PM
|
|
|
Senior
Posts: 606
Joined: Oct 2009
|
In 1951 my father purchased a new Ford F-1 with V8, three on the three, and overdrive. The truck was a custom cab with radio, heater and 16" Firestone split ring wheels... That truck was the best truck my dad ever had, I had the pleasure of driving the truck all over the western states. With the overdrive, the truck would cruise very nicely at 60 mph plus, when hills were encountered, or we had to pull a trailer, disengaging the OD gave the lower ratio we needed to pull the hills. It is a little known fact that factory equipt vehicles have a lower axle ratio than non OD vehicles. In the mid 1950's Ford started using 3.89 as the standard axle ratio for OD's, where-as non OD vehicles were somewhere around 3.73 unless the vehicle was ordered with 4.10 or lower axle ratio. As mentioned in the earlier posting to this topic, you can use the OD unit out of just about any '50/60 Ford car/truck, so long as it is compatible with your trans. Your will have to shorten the drive shaft and have the correct linkage. Sometimes the easiest way to get everything you need for the conversion is to purchase a vehicle that has a factory OD. You can also use either a Gear Vendors, Mitchel, or one of the other after market units. Your 4.27 axle ratio will still be a little low for an OD, 4.10 or 3.89 would be better. Don't let someone talk you into a gear ratio higher than 3.89 with a stock engine and a OD because you will not have enough engine to pull the higher ratios.
Bill 36 5 win delx cpe
|
supereal |
12-02-2009 @ 9:16 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
Trucks usually have a high center of gravity which amplifies any bounce or sway. A set of really good shocks can go a long way toward making the vehicle safe on the road. If the kingpins have any slop, or the steering box is loose, keeping between the fences can be a chore. Another important factor is proper toe-in adjustment. If not correct, it can set up a dangerous shimmy that requires coming to a stop to regain control. I love old trucks, but getting them in shape for long trips is a very good idea.
|
Big Red 51 |
12-02-2009 @ 6:46 AM
|
|
|
New Member
Posts: 192
Joined: Oct 2009
|
Thanks Dale and others, I may explore some of these options. Of course, I can continue to stay under 55 on the hiway. These trucks are not all that stable at higher speeds anyway. If the old 4.27 fails I will replace with a lower gear ratio. Thanks, Don
|
Dale Fairfax |
12-01-2009 @ 7:47 AM
|
|
|
Member
Posts: 20
Joined: Oct 2009
|
Assuming you have a 1/2 ton or F-1, you should be able to bolt in any '49-'59 Ford/ Merc B-W Overdrive transmission with only moderate difficulty (shortening the driveshaft; intalling some means to shift the side shift box; wiring). Or: install one of the later Ford 4 speed transmissions with the integral O.D.(4th gear is O.D.). Or: on the more complex side install a late T-5 5 speed which requires some sort of adapter plate plus shortening the drive shaft. Finally, you can search for a later rear axle assembly of the right width with a more favorable gear. (Changing the gear ratio in the existing axle can be a problem due to lack of available parts and the difficulty of working on the type of rearend end in your truck.)
|
supereal |
11-30-2009 @ 9:38 AM
|
|
|
Senior
Posts: 6819
Joined: Oct 2009
|
I believe Alan is right, but they may be able to point you toward a unit that will work. We have swapped rear axles in light trucks over the years when we were able to find them in salvage yards. Most will fit with some minor revisions to the spring pads and the driveshaft. We used that approach when we dropped a V8 into an Econoline pickup a couple of years ago. I don't think 2800 will harm your truck, but it gets really tiresome to hear the roar and feel the vibration. Most old trucks are not subjected to the loads they were designed for. Even a 10 percent reduction in rear end ratio would help. That would require a ratio in the order of 3.85, more or less.
|
ford38v8 |
11-28-2009 @ 6:22 PM
|
|
|
Senior
Posts: 2736
Joined: Oct 2009
|
Don, I don't believe the Mitchell OD will work on your truck. It's for torque tubes, not open driveshafts.
Alan
|