Early Ford V-8 Club Forum

EFV-8 Club Forum / General Ford Discussion / U joint grease

Reply to Discussion | New Discussion << previous || next >>

Posted By Discussion Topic: U joint grease -- page: 1 2     David J 02-07-2014 @ 3:14 PM reply profile send p.m. New Member Posts: 136 Joined: Jan 2014 What year are you dealing with ? I only mess with 33-34 but some stuff is basic . Is your rear end overfull ? Is your tranny overfull ? There is a seal behind the front driveshaft bearing and if it is bad your lube will head down the torque tube . Can you tell if it was leaking out the bottom of the bell ? Speedo turtle ? If it is just coming out the center pivot hole it cannot empty itself that way . Kinda hasta be the driveshaft seal , turtle gasket or the bell gaskets . Dobie 02-07-2014 @ 1:51 PM reply profile send p.m. Member Posts: 33 Joined: Nov 2010 I used a tube of the mystic grease, drove to Calif. and back there was none left. 6000 miles The u joint was wet as was the surround. The only evidence of grease was by the zert. The u joint showed some wear. supereal 02-03-2014 @ 7:06 AM reply profile send p.m. Senior Posts: 6819 Joined: Oct 2009 Genuine Ford u-joints are nearly indestructable. The repros, not so much. If there had been tight oil seals on the transmission output shaft, the story would probably be different. At one time, replacing the u-joints with the Lincoln needle bearing joints was popular, but probably not necessary. Failure is rare unless they are run dry, or abused. JM 02-02-2014 @ 8:00 PM reply profile send p.m. Senior Posts: 822 Joined: Oct 2009 I'll let my '35 Ford Fordor Sedan continue to be a documented test for determining how well John Deere Corn Head Grease works at keeping a stock/original universal joint lubricated and in good working condition. This universal had 54k miles on it when I rebuilt the rear. It now has 64k miles or 10k miles with JDCHG as its lubrication. I'm planning to drive this car to two EFV-8 C/A National meets and on several tours this year, so this should put at least another 5k miles on this UJ. If any of you plan to be at these meets, look me up, and we can discuss UJ life vs.the proper or best lubricants to be used with them . John This message was edited by JM on 2-2-14 @ 8:10 PM David J 02-02-2014 @ 4:45 PM reply profile send p.m. New Member Posts: 136 Joined: Jan 2014 If you go the gear oil route remember factory spec is 4 oz [ 1934 ] service bulletins . The 4 oz level is well below the hole in the clams so if it is leaking all over the floor your bell and tranny mount gaskets are not doing the job . If you overfill it you will indeed have it leak all over the floor as the felt - cork or whatever you use is only a wiper . Pretty sure it is in a late 1932 service bulletin where the formula for " cylinder oil - soda soap grease " is listed . Pretty much oil and you will see the key part is the use of tallow as a thickener and that is the big difference between this and wheel bearing grease . Tallow melts at the touch and the stuff for wheel bearings is 350* . I would assume by the dedication of the cornhead grease followers it must work well also . Cornhead grease is actually " 0 " viscosity and the post above points out " 00 " viscosity as working good also . I use all of these types in my tractors and equipment but not in my Fords . supereal 02-02-2014 @ 1:30 PM reply profile send p.m. Senior Posts: 6819 Joined: Oct 2009 As my friend Stroker says above, there is plenty of gear oil from the rear of the transmission to keep the grease emulsified. Soda soap grease is long obsolete, but was also specified as a wheel bearing grease. If you fill the u-joint housing with gear oil, be prepared to oil the floor of your garage. The reason there was a difference between car and truck specs is that the trucks mostly had open drive lines and u-joints. Light duty trucks were classified as "commercial cars", rather than "trucks". 40 Coupe 02-02-2014 @ 8:14 AM reply profile send p.m. Senior Posts: 1650 Joined: Oct 2009 I use 0-0 grease. it is so thin, it comes in a squeeze bottle and will recombine and not "hollow" out. Install 4 1/2 Oz through the speedometer gear hole on the torque tube using a small thin tube to get it in the u-joint area. Then use a couple of squirts with a grease gun on the u-joint cover Zerk fitting, with regular chassis grease. Ford did recommend 140W gear lube for the truck u-joint but insisted to continue to use soda soap grease on the car u-joint. I do not recommend JD cornhead for the u-joint but JD does have a video you can view of their corn head grease in action and you can decide. JM 01-31-2014 @ 9:05 PM reply profile send p.m. Senior Posts: 822 Joined: Oct 2009 I did a complete rebuild, including changing ring & pinion gears to 3.78, on the rear of my '35 Fordor sedan last spring. When reinstalling the rear, I filled the U joint housing with JD Corn Head Grease. Since then I have driven this car 10,000+ miles with no U joint problems. I also filled the steering box with JDCHG at the same time. This grease is working well in both locations with no apparent leakage. I'm planning to use this same grease in the same locations on a '35 coupe as it goes back together. John David J 01-31-2014 @ 7:20 PM reply profile send p.m. New Member Posts: 136 Joined: Jan 2014 In my 33-34 cars I just use SAE 140 in steering box , tranny , u-joint & rear end . Factory spec for 34 is 4oz and that is well below the level of the center hole in the inner bell . As pointed out already your tranny is going to slobber into the cavity anyway . To address your question cornhead grease has a dedicated-noisy following on another site . I do use it in my old JD tractors but not in my old fords . Your call of course . Old Henry 01-31-2014 @ 5:57 PM reply profile send p.m. Senior Posts: 738 Joined: Apr 2010 I decided to use the corn head grease after seeing this video of how it thins so that it doesn't let the U-joint just carve out a cavern as it would with stiffer grease. https://www.youtube.com/watch?v=UEwk_sYP6A8 So far, so good.

<< previous || next >>

PAGE: 1 2

NOTE: YOU MUST BE A REGISTERED USER AND BE LOGGED IN TO POST (and reply to) messages in this forum. If you are a first time user, please click the CREATE A NEW ACCOUNT in the masthead above to register and Log In. After that, all you do is LOG IN to enjoy using this site.

DISCLAIMER: The V-8 Club does no independent testing of any of the opinions, thoughts or suggestions presented in the website on the Forum, in the Tech Tips section, or any section. A reader should consider the website to be a forum wherein differing solutions to a particular set of circumstances may be discussed. Ultimately, the selection of an item for an individual's vehicle must be based upon the independent study of the vehicle owner in consultation with people in the hobby and restoration experts.

EFV-8 Club Forum Home | Back to Home Page | Contact the Webmaster

Copyright © 2009 - EFV-8.org
Powered by < CF FORUM > v.2.1